B2900A 2.5.1351.6139 RELEASE NOTE - NEW FEATURES Scripting (License is needed.) LED Demonstration Program (Press [More]-[LED Demo]) - FIXED DEFECTS #162299 Window2 text data is hidden when local key was pressed. #184063 I/O hangs when transferring large amount of data. #187575 Intermittent hang-up when sweep measurement is aborted by output protection. #193236 Unable to abort infinite waveform output when both two channels are busy. B2900A 2.0.1312.2910 RELEASE NOTE - FIXED DEFECTS #96216 Ib-Ic curve capability in Graph View Mode. #96222 Request to support "Infinity" as Trigger Count. #102948 Unexpected program memory status is shown. #149042 Setting conflict error doesn't happen when running on the front panel. #149362 Unexpected jumps at joint of the curves when repeating curves on list sweep with ARM:INFINITY. #149694 Unexpected hang-up after measurement with long wait and time constant. #158151 Cannot launch the web instrument on IPv6. #158884 The instrument shows "Fan speed is too fast" in RACK mode. #162283 Unexpected pop-up window is shown if USB-A (front) is connected to USB-B (rear). #177173 Application Error occurs during Sweep Measurements #179938 Hangs up by front panel operation during SCPI command is in progress. #179941 Unexpected trace configuration is shown on Trace Buffer Setup dialog. #182858 Unexpected query result on :SENSe:DATA? command. B2900A 2.0.1225.1717 RELEASE NOTE - NEW FEATURES LXI 1.4 (LXI Core, LXI HiSLIP, and LXI IPv6) - FIXED DEFECTS #77088 Wants to save trigger mode. #77090 Wants to specify the increment of knob rotating. #86917 Crash on repetitive list sweep. #87578 Wants to input "10pA" not "0.01nA". #88223 Hang up when "ABORt" command is sent during being initiated. #90979 Unexpected waveform preview on List Sweep/Edit dialogs. #95675 :ARM:TRAN:COUN? INF does not cause an error. #95791 Unexpected self-test failure on low temperature. #97269 Slow program memory execution time. #99534 LAN setting get corrupt when cable is unplugged in static IP mode. #100315 Unexpected source level when changing source mode. #100848 Unexpected glitches when current range is changed to 1A from 100mA. #102233 Source mode is not restored if it was canceled. #103657 Incorrect SCPI error messages are shown on the front panel. #104236 Empty file is created even if saving configuration failed on the front panel. B2900A 1.0.1144.9870 RELEASE NOTE - FIXED DEFECTS #4650 When mDNS is disabled with no LAN connection, AgilentLxiWebService.exe dies. #63772 Incorrect source values are fetched when ARM count is INFinite. #64217 Incorrect error message for "IADC Lost" event. #70493 Unexpected thin-out result on Graph/Roll view. #74773 Cannot show CH2 data captured during remote state with remote display off #74786 Unexpected voltage/current output when stepping voltage/current list by EXTn signals. #76607 Does not output trigger when specified only auto start sense action. #76815 Unexpected staircase sweep parameter changes when editing list sweep parameters. #85261 Crash on Reading/Buffer Overflow status bit changes B2900A 1.0.1121.1140 RELEASE NOTE - FIXED DEFECTS #49884 Unexpected DISP:ZOOM result during remote display is OFF #63182 Unexpected current value format on pulsed mode B2900A 1.0.1120.6435 RELEASE NOTE - FIXED DEFECTS #49884 Unexpected DISP:ZOOM result during remote display is OFF B2900A 1.0.1120.644 RELEASE NOTE - FIXED DEFECTS #53687 Unexpected power value format in Measure Result dialog #54235 Changed math result format in Measure Result dialog #63051 Unexpected number of auto-ohm measurements by Trigger button #63054 Incorrect V/I parameter rounding on SCPI commands #63066 Incorrect format selection on Trace Statistics Format dialog #63182 Unexpected current value format on pulsed mode #63306 Unexpected number of digits when feeding math result to Limit Test B2900A 1.0.1119.2582 RELEASE NOTE - FIXED DEFECTS #49884 Unexpected DISP:ZOOM result during remote display is OFF #53552 Unexpected interlock open error when output switch is turned on #53702 Updating firmware causes system crash when trigger system is busy #54024 Unexpected delta timestamps in trace result #54219 Showing "Trace Statistical Result" dialog causes system hang-up on single channel models #54221 Trace points cannot be set on "Trace Buffer Setup" dialog #55328 Unexpected binary/octal/hexadecimal query result (Web) #56344 Unexpected trace data is stored to USB flash memory B2900A 1.0.1118.8052 RELEASE NOTE - FIXED DEFECTS #48790 Refined binary/decimal/hexadecimal edit on several dialogs #50370 SENSe:DATA? causes system crash during measurement on 2400 mode #53168 Operation status condition register value maybe incorrect on SOCKET #53404 SMU self-test fails on Loop Control test #53496 Unexpected current range overflow when voltage measurement overflew #53552 Unexpected interlock open error when output switch is turned on #53601 Failed to initiate pulse operation when its width is 50us and period is 100us #53605 Unexpected carry control when editing values by rotary knob #53671 SMU output change should not be allowed during trigger system is busy #53672 Cannot change remote sensing with output on #53676 Inconsiderate error messages on LXI subsystem commands #53682 Unexpected enable/disable controls on Single view #53686 Unexpected "Locked" message controls for GPIB/USB connections #53687 Unexpected power value format in Measure Result dialog #53690 No error on "Load List Sweep Data" dialog #53692 Deleting all list item on "List Sweep" dialog causes system crash #53700 Cannot move up to the parent from "Empty" folder #53702 Updating firmware causes system crash when trigger system is busy #53735 No error on :INIT: when limit test is enabled #53740 Cannot change source mode when its ranging mode is fixed #53760 Unexpected operation when sweeping with auto-ohm measurement #53761 Setting more than 32 characters as math unit name causes system crash #53764 Math result may not be shown on "Measure Result" dialog #53993 Incorrect format selection result on "Format(Measure)" dialog #54024 Unexpected delta timestamps in trace result #54030 Incorrect timestamps are saved on the front panel #54093 Incorrect power check on spot/sweep panel (Web) #54138 Cannot abort when READ?/FETC? is in progress for long time